Charger M H Power Supply and Battery Charger
- Original manufacturer
- Consilium / Salwico
- Name
- Charger M H Power Supply and Battery Charger
- Model
- Charger M H
- Part number
- 5100062-01A
Supply availability and delivery time require confirmation. A catalog reference does not imply stock.
Specifications
| Manufacturer approvals / certifications | Not provided by manufacturer |
|---|---|
| Manufacturer Article Number | 5100062-01A |
| Psu Input | 28 VDC |
| Operating Voltage Range | 19-30 VDC |
| Current Consumption (at 24 V, Battery Supply Only) | 43 mA |
| Max. Output Current | 8 A |
| Cable Terminals | 2.5 mm² |
| Ntc Resistor | 10 kΩ 2%, B=3977, 3×3 |
| Ga Input Resistor | 10 kΩ |
| Operating Temperature Range | -40 °C to +85 °C (Tx) |
| Weight (with Housing) | 140 g ± 5% |
| Spare Part No. | 5100061-03A |
| Manufacturer-listed System | TS1000 (2022 V T document) |
| Address Configuration | SW1 poles 1-7 set binary physical address; it must match system configuration |
| Backbone Power Channels | SW1 pole 8: channel 1; pole 9: channel 2. ON deactivates, OFF activates |
| Power Output / Sw1 Pole 10 | ON: always active; set output to "not used" in configuration to avoid faults. OFF: programmable |
| One / Two-module Setup | Single: 8+9 OFF. Dual: module 1 8 OFF/9 ON; module 2 8 ON/9 OFF |
| Redundant Earth Supervision | For the two-module redundant method, disable earth supervision on ONE Charger M by removing its PCB jumper |
| Battery Capacity / Sw2 | Poles 1/2 ON/ON: 0-12 Ah; OFF/ON: 12-24 Ah |
| Forbidden Sw2 Settings | ON/OFF and OFF/OFF not allowed. Wrong charging setting can overcharge, undercharge or overload PSU |
| Battery Type | Valve-regulated lead-acid (AGM) batteries only |
| Ntc Sensor Location | External NTC on battery holder or as close as possible; NOT directly on battery |
| Charging Temperature Condition | External NTC adjusts charging; optimum battery performance specified between -5 °C and +40 °C |
| Deep-discharge Handling | Not designed to recover deeply discharged batteries; replace or use a separate charger designed for that purpose |
| Low-battery Output Cutoff | With charging enabled and PSU1/2 power absent: below 21 VDC ±0.5 V shuts outputs off |
| Standby / Battery Safety | Standby still draws approx.25 mA. After >1 hour, physically disconnect battery to prevent further deep discharge |
| General Alarm (morse) Scope | 24 VDC GA input via hardware to internal BBI; cabinet-common BBI only, not between stretched bus sections |
| Output Capacity Condition | Maximum power output depends on PSU capacity and Backbone Bus load |
| Ntc / Ga Indicators | NTC: green=overheat, yellow=cable break, off=OK. GA: green=general alarm active, off=OK |
| Communication / Safe-state Leds | COM green flashing: communication OK but unconfigured. PS yellow flashing + COM off: module not functional |
| Wiring Reference | Retain original p2 diagram for PSU1/2, mains/emergency monitors, power output, GA, battery and NTC terminals |
| Mounting | Mount on a horizontal 35 mm DIN rail |
| Dimensions | 99 mm high ×114 mm deep ×29 mm wide; original drawing also marks 23 mm subdimension |
Compatibility
- Requires technical confirmation; manufacturer compatibility evidence is not provided.
Accessories
- Not provided by manufacturer
Original documents & sources
Source pages
- https://www.consiliumsafety.com/content/uploads/products/en/5100062-02/5100062-01A_Charger%20M%20H_T_EN_2022_V.pdf
- https://www.consiliumsafety.com/content/uploads/products/en/5100062-02/5100062-01A_Charger%20M%20H_T_EN_2022_V.pdf
- https://www.consiliumsafety.com/content/uploads/products/en/5100062-02/5100062-01A_Charger%20M%20H_T_EN_2022_V.pdf
Original manufacturer data retained. Product enquiry and technical sourcing by MAXONE Marine. Last reviewed: Not provided.